Elite Tuckpointing

Menu

Call Us Phone

0434 345 304

Get a Free Quote!

Brick Repointing

Brick repointing before and after: cracked worn mortar beside clean joints by Elite Tuckpointing in Sydney

Brick Repointing in Sydney - Give Ageing Walls New Life

Mortar is often the first part of a masonry wall to show its age. Cracking, crumbling, recessed joints and sections that have washed away can leave the surrounding masonry more exposed to moisture and weather.

Elite Tuck Pointing provides brick repointing in Sydney for heritage homes, period properties and established brick buildings. We remove deteriorated mortar carefully and replace it with a compatible mix, paying close attention to joint depth, colour and finish, so the repair sits naturally with the existing wall.

Proper Joint Preparation

Failed mortar is removed to a suitable depth so the replacement material bonds to a sound surface rather than covering weak mortar underneath.

Compatible Mortar Selection

Mortar should suit the age and condition of the masonry. Heritage NSW recommends that repair mortar generally be weaker and more permeable than the surrounding bricks or stone.

Consistent Joint Finishing

The profile, colour and texture of the new joints are matched as closely as possible, so repaired areas do not look unnecessarily patched or uneven.

Protection for Older Masonry

A well-chosen mortar acts as the sacrificial part of the wall, allowing the joint to weather before the masonry itself and making future maintenance easier.

Red brick verandah with low wall and paved floor before brick repointing by Elite Tuckpointing in Sydney
Before
Completed residential brick repointing on a Sydney home verandah wall and columns by Elite Tuckpointing.
After

When Does the Brickwork of Sydney Properties Need Repointing?

Repointing is usually needed when mortar has become loose, powdery, cracked or noticeably recessed from the face of the bricks. Gaps between joints, sections that can be scraped away easily, and repeated patch repairs are also signs that the mortar may be reaching the end of its useful life.

On older Sydney homes, the goal is not simply to make the wall look newer. Repointing brickwork in Sydney involves removing material that has failed and replacing it in a way that suits the existing masonry. According to Heritage NSW, deteriorated brick or stone mortar can be repointed using traditional lime and sand mortar as part of appropriate heritage maintenance.

What Makes a Good Repointing Job for Homes in Sydney?

Good repointing depends on more than filling visible gaps. Preparation, mortar compatibility, joint depth, and the final finish all affect how the repair performs. For older masonry in particular, using mortar that is too hard or too dense can be counterproductive because stress and moisture may be transferred into the bricks instead of the joints. According to Heritage NSW, mortar should generally be weaker and more permeable than the surrounding masonry, allowing walls to dry through the joints after rain. Here’s what we do.
  • Failed mortar is removed before new material is applied.
  • Original brick edges are protected during joint preparation.
  • Mortar strength is chosen to suit the existing masonry.
  • Joint colour and texture are matched as closely as possible.
  • The original joint profile is considered before finishing.
  • Heritage and period properties are approached with extra care.
  • Localised deterioration can be repaired without disturbing sound areas unnecessarily.
  • Wall height, access, joint condition and preparation all influence brick repointing cost in Sydney.

Brick pointing in Sydney is sometimes used as a general term for mortar-joint repairs, while repointing specifically refers to removing deteriorated mortar from an existing wall and replacing it. The scope can vary considerably from a small section of failed joints to a complete façade, which is why the cost of repointing depends heavily on condition, access and the amount of preparation required. An inspection by our experts allows the work to be assessed properly before deciding how much of the wall actually needs attention. Talk to our team today.

Frequently asked questions

What is brick repointing?
Brick repointing is the process of removing old, deteriorated mortar from between your bricks and replacing it with new mortar. The bricks themselves usually stay put unless they’re damaged too and need separate attention.
Look for crumbly or powdery mortar, missing sections, recessed or gappy joints, loose bricks, or damp patches, especially around chimneys and exposed walls. If you can pick mortar out of a joint with your finger, it’s time to get it checked.
It really comes down to the mortar used, the quality of the workmanship, and how exposed the wall is to weather. Mortar that’s properly matched to your brickwork and installed well should give you solid, long-term protection.

Pricing varies based on wall area, access and height, how much mortar needs removing, the joint depth, and whether any brick repairs are needed alongside the repointing. Rates can vary a fair bit across Sydney, so it’s best to get a proper on-site quote rather than go off a flat rate.

  • Main menu

No Content